Deep Suction Dredger -inland use for sale

jun 19, 2020
Dredging
1 0

Deep Suction dredger for sale

built 1987 by Bagema, The Netherlands

Main dimensions: 18×7,3×2,5 (lxbxh)
Dimension pontons: 18 x 2,5 x 2,5/1,5 m.
Ladder length: 18 m.
Max. suction Depth: 35 m.
Max. discharge length: 1.700 m.
Max. head dredge pump: 8,5 bar

Total Weight: 80 ton
Dimension suction pipe: 324 x 10 mm
Dimension discharge pipe: 324 x 10 mm

Well maintained, in good condition
Easy and fast (de)mobilisation

 

Introduction
The plain suction dredger is designed and constructed to excavate sediment from a water bottom and transport it to another place via a pipeline. The excavated material is transported through floating pipes, using a hydraulically driven, submerged centrifugal dredge pump and a diesel driven jet pump. The materials that can be dredged are sludge, sand and gravel. The jet-water nozzles at the suction head loosen the material and the vacuum of the dredge pump sucks the water-solids mixture in the suction pipe. The surrounding water must not be chemically corrosive. The vessel is designed and constructed for use in sheltered waters. The output of the pump unit depends on the dredging conditions (dredging depth, delivery distance, type of material, geodetic pressure) and can be calculated from the pump characteristics as described in this technical specifications.

Operating Conditions
•The output of the pump unit depends on the dredging conditions (dredging depth,delivery distance, type of material, geodetic pressure) and can be calculated from thepump characteristics as described in the technical specifications.
•The materials that can be dredged are sludge, sand and gravel.

•The surrounding water must not be chemically corrosive.
•The dredger is equipped and protected for fresh water conditions.
•Min. operational air temperature -5° Celsius.
•Max. operational air temperature 40° Celsius.
•Max. humidity 80%.
•Sellers expressly advise against using the plain suction dredger under conditions ofswells / high waves, thick fog, strong winds and ice formation or in floating ice.
General Description
The DN350 Deep suction Dredger is a stationary plain suction dredger that can be disassembled. The dimensions are designed for transport by truck over the road. The dredger is used to dredge sand, sludge and gravel from the bottom of a river, canal or lake.
Hydraulic power is then used to transport the slurry material to the delivery location.
The hull consists of two pontoons:
•one side pontoon on the Port side
•one side pontoon on the Starboard side
The two pontoons are connected with a connection frame and support beam at the rear, a foundation frame for winches in the middle and a portal and A-frame at the front. At the Aft a portal crane is mounted for installation of dredge pipes and hoses at the Aft.
In between the two side pontoons, a hinged ladder/suction pipe is mounted. The ladder can be raised and lowered max 50° by means of an hydraulic hoisting winch (ladder winch) positioned in front of the wheelhouse. At the front of the ladder a suction pipe is connected by a cardan piece. The suction pipe can be raised and lowered max 90° by means of an hydraulic hoisting winch (dredge pipe winch) positioned in front of the wheelhouse.
From front to aft the ladder/suction pipe contains the suction head with jet nozzles and basket, a suction pipe, a cardan piece, a suction pipe, the inspection piece, the submerged dredge pump, the hydraulic drive, the discharge pipe and the jet-water pipes.
Four hydraulic hauling winches are installed for positioning the dredger.
The SB side pontoons are divided into separate compartments, from front to aft: a water ballast tanks, void, the fuel oil tank, engine room with Hydraulic pump, Caterpillar 3408 and KSB jet pump. The HPU is used to power the dredge pump and the winches
The PS side pontoons are divided into separate compartments, from front to aft: a water ballast tanks, void, the fuel oil tank, engine room with generator set, Caterpillar 3408, Reintjes Gear Box, Bagema Booster pump.

At the aft of the dredger, under the waterline, box coolers are mounted. This coolers are for cooling the 2 pcs Caterpillar 3408 diesel engine.
Equipment

Equipment:
Engine for diving hydraulic installation
And jet pump: Caterpillar 3408, 1800 rpm, 400 HP
Hydraulic system: Linde
Engine for booster pump: Caterpillar 3408 DI-TA, 1800 rpm, 400 HP
Gear box: Reintjes LAF 340, n- 2,452:1
Generator set: Perkins 35 kVA
Underwater pump: Bagema type 30-30 FGH/OW, hydraulic driven,
1.200 m3/h mixture
Booster pump: Bagema type 30-30 FGH/BW, diesel driven
Jet pump: KSB 400 m3/u @ 8 bar, diesel driven
Winch: Hydraulic driven central drum winch, 6 drums
(4 pcs mooring, 1 pcs ladder winch, 1 pcs suction pipe winch)
Status of dredge pumps wear: 50%
Other equipment
-1 pcs A-frame
-1 pcs Lifting frame
-1 pcs wheelhouse, flexible mounted, including blinds for windows
-1 pcs Davit

 

Available 3rd quarter 2020

insp/

Delivery Holland

Comments are closed.